JUST HOW TO REPLACE A BATHTUB IN YOUR BATHROOM

Just How to Replace a Bathtub in Your Bathroom

Just How to Replace a Bathtub in Your Bathroom

Blog Article

Go Services

The writer is making several great pointers on How to Install a Bathtub Yourself overall in the content down the page.


How to Install a Bathtub
Installing a bath tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also set in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This post will certainly aid you install a new bathtub in your restroom if you have already bought a new tub as well as do not need to change the plan of your previous water pipelines.
Your devices and material checklist must consist of the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Preparing for the Setup


    First of all, the sustaining structure provided with the bath should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
    Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted access that is commonly the case.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the staying water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
    Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

    Mounting the Bathtub


    Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
    The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub until the spirit level checks out level.
    To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
    Activate the water supply and check all joints and new pipework for leaks and tighten them if required. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
    Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait till the bathtub has been used at the very least when as this will certainly resolve it right into its final position.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipelines.
    If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type needs to be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
    You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not think about this motion prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing water-resistant or water-proof adhesive as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    Do you enjoy reading up on How to Install a Bathtub Yourself? Leave a comment down the page. We would be pleased to listen to your insights about this blog posting. Hoping that you visit us again in the future. I beg you take the time to distribute this blog entry if you appreciated it. Many thanks for your time spent reading it.



    Book With Us Today!

    Report this page